Request a Quote
805.528.5250       guns@apextactical.com

Services

Apex Tactical Specialties requires an official service quote to be built before sending in your firearm for services.

Please contact us at 805-528-5250 and we would be happy to assist you with any questions you may have.

Turnaround time is estimated 10-12 weeks or less (Depending upon parts availability).



S&W REVOLVER SERVICES



ACTION WORK FOR J-Frames

LEVEL I - Duty/Carry Application $155

Action is significantly smoother than factory trigger. Includes installation of the Apex J-Frame Duty Carry Kit, and appropriate action tuning. Parts included. Reliable with all types of commercially available factory ammunition manufactured in the United States.

ACTION WORK FOR K, L, N - Frames

LEVEL II - Basic $155

Action is lighter and smoother yet ignition is not compromised. Best option for carry or defensive use guns. Reliable with all types of commercially available factory ammunition manufactured in the United States.

LEVEL III - Competition/Race Grade $200

Action is significantly lighter and geared towards the competitor using either Winchester primed hand loads or commercially available factory ammunition manufactured in the United States.

LEVEL 3.5 - .22 Revolver Competition/Race Grade $250(Model 617 only).

Trigger pull is set as low as possible without compromising ignition with US Domestic Manufactured Ammunition.

LEVEL IV - High Performance Competition/Race Grade $280. Most K, L, and N frame Center Fire Models

Trigger pull is set as low as possible without compromising ignition with Hand Loaded Ammunition using Federal Primers seated to Maximum Depth per SAMMI Spec.

CYLINDER WORK

Cylinder Chamfering:
6-shot steel cylinders - $65
7 & 8-shot steel cylinders - $75
All Titanium cylinders - $85
Remove end shake (labor only) - $45
Align Crane - $45
Time Cylinder (labor only) - $100

Other Hammer & Trigger Work

Bob, skeletonize & polish old style Center Fire Revolver Hammers - $140
Smooth & polish factory serrated narrow trigger - $55
Smooth & polish factory serrated wide trigger - $65

Sight Installation Labor

Front Sight - $35
Rear Sight Blade Replacement - $35



APEX M&P SERVICES



*Any M&P with a 1/16th diameter sear return spring or a rev A Striker, noted by its black color, sent to our facility for ANY of our services will automatically get a Sear Housing Block Upgrade to accommodate a 1/8th diameter sear return spring and/or a Modern Replacement Striker for retail value of the replacement item. No Exceptions.*

M&P Sight install front and rear: $65

Select sights available from Dawson Precision, AmeriGlo, and 10-8 Performance.

Please contact for current availability, Customer provided sights can be installed upon request.

Apex Level 1 Trigger: $130 plus s&h

This package includes installing the Apex Fully Machined Sear and Ultimate Striker Block kits only. The Apex Fully Machined Sear and trigger bar are polished to run as smoothly as possible as part of this service. An approximate 3.5-4.5 lb trigger pull weight can be expected, depending on factory tolerances.

Apex Level 2 Trigger: $160 plus s&h

This package includes installing the Apex Duty Carry Action Enhancement Kit (DCAEK). The Apex Fully Machined Sear and trigger bar are polished to run as smoothly as possible as part of this service. An approximate 5-6 lb trigger pull weight can be expected, depending on factory tolerances.

OR

Level 2 Trigger - Shield Service

This package includes the installation of the Apex Fully Machined Sear, Ultimate Striker Block and appropriate fire control springs. Due to tolerance variations that occur in the manufacture of the Shield pistol, spring combinations will be matched to our sear and fine-tuned to yield a crisp, clean trigger pull. An approximate 5-6 lb trigger pull weight can be expected, depending on factory tolerances.

Apex Level 3 Trigger: $180 plus s&h

This package includes installing the Apex Competition Action Enhancement Kit (Comp AEK-Fully Machined Sear, Ultimate Striker Block, and Spring Kit). The Apex Fully Machined Sear and trigger bar are polished to run as smoothly as possible as part of this service. This will result in a reduction of trigger pull weight by approximately 4lbs (based on a starting pull weight of 7-8lbs). NOTE: For those with a NY, MA or other 10+ pound required trigger pull weight; due to heavier average spring rates, results are likely to be more significant, with a reduction of 6-7lbs.

**Competition use only**

Apex Level 4 Trigger: $250 plus s&h for Aluminum Trigger or $215 plus s&h for Polymer Trigger

*Please specify the material type of trigger body you desire. (Aluminum or Polymer)

This package includes installing the Apex Forward Set Trigger kit (FS Fully Machined Sear, FS Ultimate Striker Block, Trigger Return Spring, and FS Trigger). The Apex FS Fully Machined Sear and trigger bar are polished to run as smoothly as possible as part of this service. An approximate 4-5 lb trigger pull weight can be expected, depending on factory tolerances.

FSS Trigger Pull can be set from 6lbs to 2-2.5 with an additional cost of select springs. Please specify your desired weight.

OR

Level 4 Trigger & Shield Service: $250 plus s&h (Aluminum Trigger only)

This package includes installation of the Apex Fully Machined Sear, Ultimate Striker Block, appropriate fire control springs and Shield Action Enhancement Trigger. Due to tolerance variations that occur in the manufacture of the Shield pistol, spring combinations will be matched to our sear and fine-tuned to yield a crisp, clean-breaking trigger. An approximate 5-6 lb trigger pull weight can be expected, depending on factory tolerances.

Level 4 Shield Trigger Pull can be set from 6lbs to 3.5 with an additional cost of select springs. Please specify your desired weight.

designed by design laurels